Technical Services
Botou Songzheng Cold Bending Machinery Factory (http://) Li Guangtao (13613270086)
The deviation of the pressing machine out of the board is a problem often encountered in the working process of the pressing machine. How to solve this problem is also the knowledge that the operator of the pressing machine should master. The following is a summary of the problems encountered by the factory during the installation and commissioning process, providing a reference for the mechanical operators:
1. The distance between the rack and the main unit affects the deviation. In order to save space, some color steel plate manufacturers have too close distance (within 2 meters) to the feeding inlet of the main frame of the tile pressing machine, which causes the feeding port to be unable to control the color steel plate, causing the plate to run off. The correct placement method should be that the distance between the discharge rack and the main machine of the tiler is kept at five meters. Even if the discharge rack is not placed very positively, the feed port can adjust the feeding state of the color steel plate. Solve the problem of deviation.
2. The feed port adjustment is not suitable. During the installation and commissioning of the tile press, the commissioner will generally adjust the size of the feed port to a suitable position. After the fastening screws are fixed, the feed position and size will not change. However, some equipment changes during the use of the feed port, causing the board to run off. The user can first fix a section on both sides of the inlet, press the board and then adjust the other side. After the dimension measurement is completed, it is required that the degree of compression on both sides is neither gap nor hanging. The feed port thus adjusted can play the role of adjusting the feeding of the color steel plate.
3. During the work process, the feed status should be closely monitored. In general, the feed state of the sheet should be that the feed plane is lower than the feed gate control height. However, in some cases, the feeding plane of the sheet will be higher than the control height of the inlet, resulting in an uncontrolled state of the feed. At this time, the worker should stop the inspection and adjust the feeding state of the sheet appropriately.
4, to ensure that the shape of the pressure wheel is good. When the tile pressing machine is working, the plate is gradually formed in a trapezoidal shape during the pressing process. Therefore, the degree of centering of the pressing wheel of the pressing machine is very important. Under normal circumstances, the middle wheel of each row of the shaft is subject to the The middle wheel must be on a straight line. When pulling the center line, the thinner the line, the higher the degree of centering of the adjusted profile wheel. The low degree of homing is also a cause of the deviation of the pressure plate machine.
5. The gap between the upper and lower wheels is evenly adjusted. When adjusting the gap between the upper and lower wheels, it is very important to keep the gap between the upper and lower wheels of each row and the upper and lower wheels of each row of wheels uniform. The gaps are inconsistent, especially the inconsistency of the upper and lower press-type wheel gaps on the left and right sides of each row of shafts is a very important reason for the deviation of the pressure plate machine. The most common and simplest and most effective way to adjust the gap is to measure with a feeler gauge.
The above are some common phenomena that Songzheng Machinery encountered when debugging equipment for customers. Of course, the factors affecting the deviation of the pressure plate machine out of the plate are not limited to these, which requires the user to continuously summarize and correct in time during the long-term use. At the same time, it is also very necessary to communicate frequently with the technicians of the manufacturers. Only in this way can your machinery be kept in good working order from time to time.
Http://news.chinawj.com.cn
Submission:
This NFC Elastic Wristbands with elastic function, in dia 80mm, 24mm width, are super easy to put on your wrist, look great with YOUR logo by weave.
If you need weatth and waterproof, we can put a PPS hard tag in side.
If you just in normal using, we can put a pet tag in side to save the cost.
Ideal for making your next event, party or festival a memorable experience!
NFC Elastic Wristbands can be embedded 125Khz chips like Tk4100, EM4200, T5577, EME44305 and Hitag etc.
NFC Elastic Wristbandsan be embedded 13.56MHZ chips like Ntag213, NTAG215, NTAG216, Mifare Classic, Desfire EV2/EV2, Plus X, Plus SE, ICODE, Ultralight, TI 2084, Topaz512, and F08 etc.
NFC Elastic Wristbandsan be embedded 860MHZ-960MHZ chips like Alien H3, Alien H4, U-Code Gen2 and Impinj M4/M5 etc.
Besides, SunwayRFID also provide rfid silicone wristband, RFID Bracelet, pvc wristbands, RFID Keychain, RFID Tag and rfid cards too, one-shop can meet all your need about RFID.
Price, customer service, and quality always at our first place!
NFC Elastic Wristbands
RFID Elastic Wristband,NFC Elastic Wristbands,NFC Elastic RFID Wristbands,Elastic Wristband
Sunway Smartech Co.,LTD , http://www.sunwayrfid.com