First, cleaning our after-sales and inspection process found that many people who have used engraving machines think that engraving machines do not have to be clean. They can also say that they do not need to be basically clean. When they are used, they should properly clean the countertops. Why? ? Because they all think that the engraving machine work process itself is a lot of dust, that is to say that he itself is the application of dust in the dust, if you go to clean up every day, then how much trouble, so many people are not only not clean up, but also It's not right for the machine to be full of things. The correct approach is:
1. The countertops should be cleared in time after the work is completed, which will provide convenience for the next work.
2. Clean the material swarf next to the guide rails and guide rails to prevent the jamming machine from causing jamming during the work process.
3, regular cleaning of the screw, to prevent sticky foreign objects on the screw, screw in the device is very important, he decided the accuracy of the machine, and the screw in the transmission process also plays an important role.
4, regular cleaning technology control box, dust board when the biggest killer.
Second, oiling Some customers because of better business, equipment, workload is also relatively large, often forget to oil the machine, some customers because of seasonal reasons, equipment does not work for days or even weeks, do not pay attention to equipment oil Work, our work experience tells us that oiling plays an important role in the maintenance of the engraving machine. In the autumn and fall, our technical department puts forward the maintenance of engraving machine oil. The correct approach is:
1, first clean the rails and screws, can be used cloth (not hair removal) bar rails and screw on the oil and material debris cleared. Due to the low temperature, the guide rail and screw can be added with oil, it is best to add antifreeze oil.
2, the refueling cycle is twice a month, that is, plus oil once every two weeks.
3. If the machine is not used for a long period of time, it should be regularly aired to ensure the flexibility of the drive system.
4. Move slowly back and forth after adding oil to ensure that the lubricant can be evenly added to the guide rail and the screw.
Third, the impact of temperature and temperature on the engraving machine is not great, but because many customers add butter to the screw, the winter also forgot to clean up, resulting in each boot does not open, and some studio temperatures are low, although added oil, Can still be frozen, the machine does not run, we think:
1, to ensure that the operating room environment temperature, it is best to reach room temperature, at least the staff will not be very cold.
2. Check the applicable temperature of the refueling standard and at least reach the minimum temperature.
3, when the machine is not in use, if the room temperature is lower, it is better to pour out the water in the tank to prevent freezing of the water tank and the water pipe.
Fourth, cooling water Many customers often forget to change the water, especially in autumn and winter, due to low outside temperature, spindle motor heat is difficult to feel it out, we hereby remind customers:
1. The cooling water is a necessary condition for the normal operation of the spindle motor. If the cooling water is dirty, it will cause serious damage to the motor and ensure the clean cooling water and the normal operation of the pump.
2, pay attention to the water level, must not make water-cooled spindle motor water shortage phenomenon, so that motor heat can not be exported in time.
3, pay attention to the ambient temperature, be careful because the water temperature is too cold and cause the tank and the water pipe to crack.
4, conditions can use antifreeze cooling.
Fifth, computer abnormalities in the computer will also cause many problems, especially for the computer connected to the engraving machine, we found during the maintenance process, computer abnormalities also caused us to repair a lot of unnecessary trouble, but also delayed the customer's business, our technical department Summarized, put forward customer computer maintenance attention to several aspects:
1. Regularly clean the chassis dust, pay attention to the heat dissipation of the chassis, be careful that excessive dust caused an error in the industrial control card.
2, regular disk defragmentation, optimize the computer system,
3, regularly killing the virus, but pay attention to work can not open the degree of anti-virus, careful interference.
Bulk Blending Fertilizer (BB Fertilizer/Mixture of Fertilizer) is a kind of compound granular fertilizer mixed by several single fertilizers or compound fertilizers according to certain proportion. It has characters of granule uniformity, less water, moderate granule intensity, no agglomeration, easy to use and low cost.
The formulation (N,P,K content) of BB Fertilizer can be flexibly changed according to the crop`s nutrition requirement, local soil fertility, crops growing levels and other conditions, therefore BB Fertilizer is more scientific and targeted especially for balance fertilization.
Balanced Fertilizer refers to a balanced fertilizer with NPK.
Balanced Fertilizer
Balanced Fertilizer,Micronutrient Zinc Sulphate Hyptahydrate,Micronutrient Zinc Sulphate Monohydrate
SHIJIAZHUANG HAN HAO TRADE CO., LTD. , http://www.hhfertilizers.com