Xingmin Weiye is a manufacturer specializing in the production of new building formwork support composite structures. The vertical tie rods are all produced by themselves and are very professional manufacturers of steel pipes. Xingmin Weiye reminds buyers that there are many kinds of steel pipes, so we must pay attention to check the quality of steel pipes.
Xingmin Weiye teaches you to identify fake steel pipes:
1. Fake and inferior steel pipes are prone to folding.
Folding is a variety of fold lines formed on the surface of a steel pipe that tends to extend throughout the longitudinal direction of the product. The reason for the folding is that the inferior manufacturer pursues high efficiency, the amount of pressing is too large, and the ear is generated, and the next rolling causes folding, and the folded product is cracked after being bent, and the strength of the steel is greatly reduced.
2. The appearance of fake steel pipes often has pockmarks.
The pockmark is a defect caused by the irregularity of the surface of the steel due to the serious wear of the groove. Due to the pursuit of profit by shoddy steel pipe manufacturers, the most frequent rolling mill rolling is exceeded.
3. The surface of the fake steel pipe is prone to scarring.
There are two reasons for this: (1). The material of the fake steel pipe is uneven and has many impurities. (2). The fake inferior material manufacturer's guiding equipment is simple and easy to stick steel. These impurities are easy to cause crusting after biting the roller.
4. The surface of the fake inferior material is prone to cracks because the billet is adobe, the adobe has many pores, and the adobe is cooled.
During the process, cracks are generated due to thermal stress, and cracks occur after rolling.
5. Fake and inferior steel pipes are easy to scratch, because the equipment of the fake and inferior steel pipe manufacturers is simple, easy to produce burrs and scratch the surface of the steel. Deep scratches reduce the strength of the steel.
6. The fake steel tube has no metallic luster and is light red or similar to pig iron. The reason is two points. The billet is adobe. 2, the temperature of the fake inferior material rolling is not standard, their steel temperature is measured by visual inspection, so that the rolling can not be carried out according to the specified austenite region, the performance of the steel naturally cannot meet the standard.
7. The cross-fabricity of the inferior steel pipe is thin and low, and the phenomenon of filling and dissatisfaction often occurs. The reason is that the manufacturer has reached a large negative tolerance, the amount of reduction of the first few passes of the finished product is too large, the iron type is small, and the hole type is not full.
8. The cross section of the inferior steel pipe is elliptical. The reason is that the manufacturer has to reduce the amount of the two rolls in front of the finished roll in order to save material. The strength of the rebar is greatly reduced, and it does not meet the standard of the rebar size. .
9. The composition of high-quality steel is uniform, the tonnage of the cold-shearing machine is high, and the end face of the cutting head is smooth and tidy. However, due to poor material, the surface of the cutting head often has a phenomenon of falling meat, that is, unevenness and no metallic luster. And because the fake inferior products manufacturers have fewer heads, big ears will appear at the head and tail.
10. The fake steel pipe material contains many impurities, the density of the steel is too small, and the size is too bad, so in the absence of the vernier caliper, it can be weighed and checked. For example, for rebar 20, the national standard specifies a maximum negative tolerance of 5%. At a fixed length of 9 M, its single theoretical weight is 120 kg. Its minimum weight should be: 120 X (l-5%) = 114 kg. The actual weight of a single root is less than 114 kilograms, which is a fake steel because its negative tolerance exceeds 5%. In general, the effect of the phasing weighing will be better, mainly considering the problem of cumulative error and probability theory.
11. The inner diameter of the inferior steel pipe fluctuates greatly because of the reason; l, the steel temperature is unstable and there is a yin and yang surface. 2. The composition of steel is not uniform. 3. Due to the simplistic equipment, the foundation strength is low, and the rolling mill has a large bounce. There will be a large change in the same week, and such a steel bar is unevenly stressed and easily broken.
12. The trademarks and printing of quality pipes are relatively standardized.
13. Three steel pipes with a diameter of 16 or more, the spacing between the two trademarks is above IM.
14. The longitudinal reinforcement of the counterfeit steel rebar is often wavy.
15. The fake steel pipe manufacturers have loose packaging because they do not have driving. The sides are oval.
The steel pipe of Xingmin Weiye is produced by Xingmin Weiye itself, so the above problems will never occur. Please rest assured that no matter which manufacturer you buy, you must check whether the quality of the steel pipe is qualified.
Lamp Box Fabric Coating,Glow In The Dark Paint,Glow In The Dark Spray Paint,Glow Paint
Guangzhou Quanxu Technology Co Ltd , http://www.skychema.com